From Hentschel
(→/etc/network/interfaces) |
(→PiAware) |
||
Line 47: | Line 47: | ||
=== PiAware === | === PiAware === | ||
* build instructions [https://flightaware.com/adsb/piaware/install at this link] | * build instructions [https://flightaware.com/adsb/piaware/install at this link] | ||
+ | * config file in boot: | ||
+ | <pre> | ||
+ | # Should piaware use the wired ethernet port | ||
+ | # for network access? | ||
+ | |||
+ | wired-network yes | ||
+ | # Wired network configuration: | ||
+ | wired-type static | ||
+ | wired-address 192.168.1.97 | ||
+ | wired-netmask 255.255.255.0 | ||
+ | wired-broadcast 192.168.1.255 | ||
+ | wired-gateway 192.168.1.1 | ||
+ | wired-nameservers 192.168.1.2 | ||
+ | |||
+ | # Should piaware use a wifi adaptor for network access? | ||
+ | # If you are using a Pi 3, this will use the built-in wifi. | ||
+ | # Otherwise, you will need to attach a supported USB wifi adaptor. | ||
+ | |||
+ | wireless-network yes | ||
+ | # To include quotation marks (") in a quoted value, use \" | ||
+ | # To include a backslash (\) in a quoted value, use \\ | ||
+ | wireless-ssid h**l | ||
+ | wireless-password ****** | ||
+ | wireless-type dhcp | ||
+ | </pre> | ||
+ | * add empty file named 'ssh' to boot partition to enable ssh |
Revision as of 16:06, 19 May 2019
Contents
Stratux
- Stratux build page this link
- Status info at http://stratux/getStatus
/etc/network/interfaces
auto lo iface lo inet loopback allow-hotplug eth0 iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet static address 192.168.10.1 netmask 255.255.255.0 post-up /usr/sbin/stratux-wifi.sh wireless-power off allow-hotplug wlan1 iface wlan1 inet static wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf address 192.168.1.98 netmask 255.255.255.0 gateway 192.168.1.1 # iface name_of_WPA_Config inet dhcp # iface name_of_other_WPA_Config inet dhcp ## End of interfaces
/etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev update_config=1 network={ ssid="h**l" scan_ssid=1 key_mgmt=WPA-PSK psk="**********" priority=1 }
PiAware
- build instructions at this link
- config file in boot:
# Should piaware use the wired ethernet port # for network access? wired-network yes # Wired network configuration: wired-type static wired-address 192.168.1.97 wired-netmask 255.255.255.0 wired-broadcast 192.168.1.255 wired-gateway 192.168.1.1 wired-nameservers 192.168.1.2 # Should piaware use a wifi adaptor for network access? # If you are using a Pi 3, this will use the built-in wifi. # Otherwise, you will need to attach a supported USB wifi adaptor. wireless-network yes # To include quotation marks (") in a quoted value, use \" # To include a backslash (\) in a quoted value, use \\ wireless-ssid h**l wireless-password ****** wireless-type dhcp
- add empty file named 'ssh' to boot partition to enable ssh