From Hentschel
(→PiAware) |
|||
(6 intermediate revisions by the same user not shown) | |||
Line 3: | Line 3: | ||
* Stratux build page [http://stratux.me this link] | * Stratux build page [http://stratux.me this link] | ||
* Status info at http://stratux/getStatus | * Status info at http://stratux/getStatus | ||
+ | * radios: | ||
+ | ** 978 UAT: NESDR Nano2 978, 29ppm (stx:978:29) | ||
+ | ** 1090 ES: NESDR Nano2 1090, 28ppm (stx:1090:28) | ||
+ | * change SDR id string for use with stratux: | ||
+ | ** stop stratux service | ||
+ | systemctl stop stratux | ||
+ | :* find radio device number | ||
+ | sdrs | ||
+ | :* write eeprom in radio | ||
+ | rtl_eeprom -d 0 -s <String>:<Freq>:<PPM> | ||
+ | :: string format see above | ||
+ | |||
+ | ==== AHRS board ==== | ||
+ | * schematics here: https://github.com/stratux/ahrs/blob/master/AHRS.pdf | ||
==== /etc/network/interfaces ==== | ==== /etc/network/interfaces ==== | ||
Line 73: | Line 87: | ||
</pre> | </pre> | ||
* add empty file named 'ssh' to boot partition to enable ssh | * add empty file named 'ssh' to boot partition to enable ssh | ||
+ | * get status | ||
+ | sudo piaware-status | ||
+ | * restart service | ||
+ | sudo systemctl restart piaware |
Latest revision as of 01:00, 29 May 2019
Contents
Stratux
- Stratux build page this link
- Status info at http://stratux/getStatus
- radios:
- 978 UAT: NESDR Nano2 978, 29ppm (stx:978:29)
- 1090 ES: NESDR Nano2 1090, 28ppm (stx:1090:28)
- change SDR id string for use with stratux:
- stop stratux service
systemctl stop stratux
- find radio device number
sdrs
- write eeprom in radio
rtl_eeprom -d 0 -s <String>:<Freq>:<PPM>
- string format see above
AHRS board
- schematics here: https://github.com/stratux/ahrs/blob/master/AHRS.pdf
/etc/network/interfaces
auto lo iface lo inet loopback allow-hotplug eth0 iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet static address 192.168.10.1 netmask 255.255.255.0 post-up /usr/sbin/stratux-wifi.sh wireless-power off allow-hotplug wlan1 iface wlan1 inet static wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf address 192.168.1.98 netmask 255.255.255.0 gateway 192.168.1.1 # iface name_of_WPA_Config inet dhcp # iface name_of_other_WPA_Config inet dhcp ## End of interfaces
/etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev update_config=1 network={ ssid="h**l" scan_ssid=1 key_mgmt=WPA-PSK psk="**********" priority=1 }
PiAware
- build instructions at this link
- config file in boot:
# Should piaware use the wired ethernet port # for network access? wired-network yes # Wired network configuration: wired-type static wired-address 192.168.1.97 wired-netmask 255.255.255.0 wired-broadcast 192.168.1.255 wired-gateway 192.168.1.1 wired-nameservers 192.168.1.2 # Should piaware use a wifi adaptor for network access? # If you are using a Pi 3, this will use the built-in wifi. # Otherwise, you will need to attach a supported USB wifi adaptor. wireless-network yes # To include quotation marks (") in a quoted value, use \" # To include a backslash (\) in a quoted value, use \\ wireless-ssid h**l wireless-password ****** wireless-type dhcp
- add empty file named 'ssh' to boot partition to enable ssh
- get status
sudo piaware-status
- restart service
sudo systemctl restart piaware