Stratux and PiAware - Revision history

Thomas at 07:00, 29 May 2019

2019-05-29T07:00:41Z

2019-05-22T23:27:08Z

2019-05-21T07:02:14Z

‎Stratux

2019-05-21T07:02:00Z

‎Stratux

2019-05-21T07:01:22Z

‎Stratux

2019-05-20T22:14:27Z

‎Stratux

2019-05-19T22:38:33Z

‎PiAware

2019-05-19T22:06:46Z

‎PiAware

2019-05-19T08:37:33Z

‎/etc/network/interfaces

2019-05-19T08:35:11Z

‎Stratux

@@ Line 14: / Line 14: @@
    rtl_eeprom -d 0 -s <String>:<Freq>:<PPM>
 :: string format see above
 ==== /etc/network/interfaces ====
 <pre>

@@ Line 5: / Line 5: @@
 * radios:
 ** 978 UAT: NESDR Nano2 978, 29ppm (stx:978:29)
-** 1090 ES: NESDR Nano2 1090, 26ppm (stx:1090:26)
+** 1090 ES: NESDR Nano2 1090, 28ppm (stx:1090:28)
 * change SDR id string for use with stratux:
 ** stop stratux service

@@ Line 9: / Line 9: @@
 ** stop stratux service
    systemctl stop stratux
-:* find radion device number
+:* find radio device number
    sdrs
 :* write eeprom in radio

@@ Line 9: / Line 9: @@
 ** stop stratux service
    systemctl stop stratux
-** find radion device number
+:* find radion device number
    sdrs
-** write eeprom in radio
+:* write eeprom in radio
    rtl_eeprom -d 0 -s <String>:<Freq>:<PPM>
 :: string format see above

@@ Line 6: / Line 6: @@
 ** 978 UAT: NESDR Nano2 978, 29ppm (stx:978:29)
 ** 1090 ES: NESDR Nano2 1090, 26ppm (stx:1090:26)
+* change SDR id string for use with stratux:
 ==== /etc/network/interfaces ====
 <pre>

@@ Line 3: / Line 3: @@
 * Stratux build page [http://stratux.me this link]
 * Status info at http://stratux/getStatus
 ==== /etc/network/interfaces ====

← Older revision		Revision as of 22:38, 19 May 2019
Line 73:		Line 73:
	</pre>		</pre>
	* add empty file named 'ssh' to boot partition to enable ssh		* add empty file named 'ssh' to boot partition to enable ssh
		+	* get status
		+	sudo piaware-status
		+	* restart service
		+	sudo systemctl restart piaware

← Older revision		Revision as of 22:06, 19 May 2019
Line 47:		Line 47:
	=== PiAware ===		=== PiAware ===
	* build instructions [https://flightaware.com/adsb/piaware/install at this link]		* build instructions [https://flightaware.com/adsb/piaware/install at this link]
		+	* config file in boot:
		+	<pre>
		+	# Should piaware use the wired ethernet port
		+	# for network access?
		+
		+	wired-network yes
		+	# Wired network configuration:
		+	wired-type static
		+	wired-address 192.168.1.97
		+	wired-netmask 255.255.255.0
		+	wired-broadcast 192.168.1.255
		+	wired-gateway 192.168.1.1
		+	wired-nameservers 192.168.1.2
		+
		+	# Should piaware use a wifi adaptor for network access?
		+	# If you are using a Pi 3, this will use the built-in wifi.
		+	# Otherwise, you will need to attach a supported USB wifi adaptor.
		+
		+	wireless-network yes
		+	# To include quotation marks (") in a quoted value, use \"
		+	# To include a backslash (\) in a quoted value, use \\
		+	wireless-ssid h**l
		+	wireless-password ******
		+	wireless-type dhcp
		+	</pre>
		+	* add empty file named 'ssh' to boot partition to enable ssh

@@ Line 29: / Line 29: @@
 # iface name_of_other_WPA_Config inet dhcp
 ## End of interfaces
 </pre>
 === PiAware ===
 * build instructions [https://flightaware.com/adsb/piaware/install at this link]